06/25/2012

New Low-e Glass or Window Film? A Comparison to Help You Decide

By Steve DeBusk

 
Which is the right choice for your facility? A comparison of low e-glass and window film.

According to the U.S. Department of Energy, 25 to 35% of energy wasted in buildings is due to inefficient windows. The California Energy Commission estimates that around 40% of a typical building’s cooling requirements are due to solar heat gain through windows. Given these facts, it’s likely that you could make big strides in energy savings by improving this exterior building element.

When it comes to making sure your windows are as energy-efficient as possible, you’ve got a few options. So that you can make the best choice for your facility, we’re comparing standard solar-control window film, low-e window film, and low-e window characteristics. We’re evaluating these choices based on:

  1. Insulating performance. During cold weather, the insulating effect of windows has a direct impact on how the interior space feels. The better the window’s insulating performance, the warmer the room feels in cold weather. According to the Efficient Windows Collaborative, when glass surface temperatures fall below 52 degrees F. is when building occupants start to notice thermal discomfort.
  2. Payback and ROI. When installing new windows or window film, the amount of time it will take to see a payback is important; if payback is quick, it’s more likely to be a realistic option for your facility.
  3. Initial cost. Upfront costs are top-of-mind for any commercial building purchase.
  4. Installation process. The installation method used, and the amount of time required to install new windows or window film, is a factor to take into consideration. Building occupants may need to be temporarily relocated, and parts of the building may not be accessible during certain periods of time.
  5. Warranty. Knowing how long you have to report problems or correct installation issues can save headaches down the road if you discover a problem with your windows or window film.
  6. Effect on outdoor views. Saving energy is important, but you don’t want those efforts to prevent building occupants from being able to see outside and enjoying views while they’re inside.

Standard window films (Reflective and lower-reflectance films)

Insulating Performance

U-value and emissivity values vary for standard window films, depending on the type of film, with emissivity values ranging from 0.70 to 0.81, which means that 19 to 30% of the room’s heat is reflected back into the room in the winter to help reduce heating costs.

While providing excellent savings during cooling season, these window films reduce solar gain through windows year-round, even when heat gain might be helpful (during the winter). In climates with prolonged heating seasons, these window films can increase the amount of heat needed from the building’s HVAC system.  Overall, these films provide excellent net savings and an attractive ROI.

Typical ROI depends on many factors for any window film or window replacement project, such as type of film, window-to-wall ratio, type of existing glass, energy rates, type of heating and cooling system, overhangs, adjacent buildings, etc. For this article, a modern 10-story, 150,000-square-foot building was used as the model. It was evaluated for energy savings across a variety of climates based on national average energy rates using the U.S. Department of Energy’s EnergyPlus program.

ROI and Initial Cost

ROI for reflective standard window film: 2 to 5 years

ROI for lower reflectance window films: 3 to 6 years

The total installed cost of standard window film products can range from $4 to $6 per square foot.

Installation Process

These window films are installed on the interior of the window, which means that building occupants will most likely need to be relocated for a very short time (sometimes only a matter of minutes) for the installation process, depending on how close they are to the windows. Being in the same room as the installation has no negative effects on occupants. Installers place drop cloths on the floor and cover/move furniture, if necessary. Then they clean and prep the glass, and use a special mounting solution, squeegee, and cutting blades to fit the film to the glass. It’s a fairly quiet process, and shouldn’t be too intrusive for occupants nearby. Once the film is applied, building occupants can move back to their spaces (if they had to relocate). It can take from a few days up to a month for the film to completely cure and bond to the glass, depending on climate and the type of window film. It’s recommended that nothing is placed on the windows (tape, window clings, signs, etc.) until the film is completely cured.

Warranty

10-18 years for commercial buildings

Effect on Occupants and Outdoor Views

How the outdoors look through standard window film depends on the type of film you choose. Darker window film reduces the amount of sunlight streaming into the interior space; darker (less than 20% visible light transmission) or reflective films (visible reflectance of 30 percent or more) can make it difficult to see outside on a cloudy/rainy day or at night.

With most window films, building occupants will still be able to enjoy views to the outdoors on the vast majority of days, although the scenery may appear darker if a low visible light transmission film (less than 20%) is used. With reflective window film, shades, drapes, or blinds might be necessary to reduce unwanted reflections or provide privacy at night.

Low-e window films

Insulating Performance

Low-e window film U-value and emissivity values can range, depending on the type of film. Conventional low-e window film has an emissivity rating of 0.33, which means that 67% of the room’s heat is reflected back into the room in the winter. There are newer low-e window films available with emissivity ratings as low as 0.07, which means that 93 percent of the room’s heat is reflected back into the space. Traditional low-e window film improves insulating performance of existing windows by 44%; higher-performance, newer low-e window film can improve insulating performance by as much as 92%.

Low-e films offset the loss of free solar heat during the heating season (unlike standard window films) and normally provide both cooling and heating savings. Low-e films improve window insulating performance 24/7, while only limiting solar heat gain in winter for 2-3 hours per day on sunny days (which are less frequent than in warmer months). The low-e coating reduces heat loss in the winter; during the summer, it reduces non-solar heat gain.

ROI and Initial Cost

Payback for low-e films ranges from 2-5 years. These films usually offer a faster ROI due to all-season performance and typically high heat rejection properties in summer. Low-e window film can be installed in most commercial spaces for between $5 and $8 per square foot. Some recently introduced high visible light transmission low-e films (70% visible transmission) are more expensive, with installed costs of $12 to $15 per square foot. Payback figures shown do not include these high light transmission low-e films.

Installation Process

The same process is followed as installation processes for standard window films (see above).

Warranty

Warranties for these products range from 7 to 15 years. Newer low-e films offer the longer warranties.

Effect on Occupants and Outdoor Views

Newer low-e films are designed to be spectrally selective and reflect infrared light while allowing visible light to pass through. This allows natural lighting into a space while minimizing heat allowed through the windows. Some older, conventional low-e films can display an iridescent appearance when installed near certain types of energy-efficient lighting (like compact fluorescents). Newer low-e coatings are available that virtually eliminate this iridescence.


Pages: 1  2  View All  
 


Visit our website today to learn about the design flexibility of a Morton building and the endless possibilities of partnering with our designBUILD team.


Wood construction is both cost and energy efficient. Check out Morton Buildings and our designBUILD team online today to discover all the benefits of post-frame construction.


When choosing a metal-clad building for your next construction project, consider Morton Buildings, Inc., and their designBUILD team, we’ll make your dream a reality.

We Can Help You Reduce Energy by 30%

Our mission is to help our customers manage their buildings' energy costs, improve reliability, and enhance performance while having a positive impact on the environment.
CLICK HERE to find out how.

 

Add highly responsive multi-zone comfort to any building project, in any climate. Our CITY MULTI H2i R2- and Y-Series VRF systems give you flexibility to fit the needs of any building. Enjoy 100% heating capacity at 0°F outdoor ambient, and 85% heating capacity at -13°F outdoor ambient.  For more information, log on to www.mitsubishipro.com

 


Tennant Company is a recognized leader in designing, manufacturing and marketing solutions that help create a cleaner, safer, healthier world. With thousands of satisfied customers already using award winning ec-H2O technology, why not see what you're missing? Test ec-H2O on your soils in your facility. Get a free demo.


Tennant Company is a recognized leader in designing, manufacturing and marketing solutions that help create a cleaner, safer, healthier world. With thousands of satisfied customers already using award winning ec-H2O technology, why not see what you're missing? Test ec-H2O on your soils in your facility. Get a free demo.

 

Replace core drilling with Connectrac In-Carpet and On-Floor Wireways, the proven connectivity solution in open interior spaces of all kinds. These elegant low-profile wireways are great for AV / telecom connectivity wherever it’s needed.

Bluebeam® Revu® simplifies digital facilities document management from design review to leveraging as-builts, maintenance manuals and O&Ms submittals.


Visit our website today to learn about the design flexibility of a Morton building and the endless possibilities of partnering with our designBUILD team.


Wood construction is both cost and energy efficient. Check out Morton Buildings and our designBUILD team online today to discover all the benefits of post-frame construction.


When choosing a metal-clad building for your next construction project, consider Morton Buildings, Inc., and their designBUILD team, we’ll make your dream a reality.

We Can Help You Reduce Energy by 30%

Our mission is to help our customers manage their buildings' energy costs, improve reliability, and enhance performance while having a positive impact on the environment.
CLICK HERE to find out how.

 

Add highly responsive multi-zone comfort to any building project, in any climate. Our CITY MULTI H2i R2- and Y-Series VRF systems give you flexibility to fit the needs of any building. Enjoy 100% heating capacity at 0°F outdoor ambient, and 85% heating capacity at -13°F outdoor ambient.  For more information, log on to www.mitsubishipro.com

 


Tennant Company is a recognized leader in designing, manufacturing and marketing solutions that help create a cleaner, safer, healthier world. With thousands of satisfied customers already using award winning ec-H2O technology, why not see what you're missing? Test ec-H2O on your soils in your facility. Get a free demo.


Tennant Company is a recognized leader in designing, manufacturing and marketing solutions that help create a cleaner, safer, healthier world. With thousands of satisfied customers already using award winning ec-H2O technology, why not see what you're missing? Test ec-H2O on your soils in your facility. Get a free demo.

 

Replace core drilling with Connectrac In-Carpet and On-Floor Wireways, the proven connectivity solution in open interior spaces of all kinds. These elegant low-profile wireways are great for AV / telecom connectivity wherever it’s needed.

Bluebeam® Revu® simplifies digital facilities document management from design review to leveraging as-builts, maintenance manuals and O&Ms submittals.


 
comments powered by Disqus

Related Products

Interiors
Interiors
Communications

Sponsored Links